CST3607 Class Notes 2018-11-01

News and Tools

  • Podnutz Pro: Talks about working with and the needs of small businesses, and the technology, and processes used.
  • StartPage.com: Is a proxy to searching Google.com, with privacy protection. Anonymizes your search. Other search engines deliver results based on what they know about you rather than giving you equal access to the Internet.

Lab-03 Debriefing

  • Compare Routing Table Worksheet with the output of “show ip route” from each router.

Decoding the output from “show ip route”

This is one entry from: show ip route

O  90.125.0.0 [110/74] via 18.1.25.2, 05:29:08, Serial0/0

ORouting protocol “OSPF”
90.125.0.0Remote network
[110Administrative Distance (AD)
/74]OSPF cost
via 18.1.25.2Next hop for the 18.0.0.0 /8 network
05:29:08Aging time. How long the protocol has been running?
Serial0/0Exit interface

Reference:

Router Configuration Checklist

  • Identify the interfaces on the router that are going to be used.
  • Identify the directly connected networks.
  • Configure the IP address and subnet mask on only those interfaces on the router that are going to be used.
  • Enable the interface(s) : no shutdown
  • Add the routing protocol
    • Add only the network address for each “directly connected” network

Cisco IOS

  • Adding an IP address to an interface
  • Adding the RIP routing protocol
  • Troubleshooting/Status commands
  • Routing protocols
  • How to configure:
    • Serial Ports
      • DCE vs DTEClock Rate on DCE end onlyshow controller serial0/0
      OSPF Routing Protocol
      • Uses the Wildcard mask, instead of the subnet mask
      DHCP via Cisco IOS
      • Set the rangeexclude addresses for static IP’s from the DHCP pool
  • Cisco IOS and Router Command Reference

Router Simulator (RouterSim)

Lab-04: (Configuring Router interfaces, and the RIP Routing Protocol)

  • You’ll need a USB Flash drive with at least 200MB of free space to save your labs.
  • When saving, always increment the version number at the end of the filename every time you save. And, save often.
  • Instructions (PDF)
  • Network Diagram (PDF)
  • The lab must be done in RouterSim
    • RouterSim is available in any of the CST computers in the Namm building. (4th & 9th floors)
  • Note: Substitute the # within an IP address with the number assigned to you in class. Use all other octets/digits, as written.
  • After you’ve verified that all of your configurations are complete and accurate, and you’re able to ping from host A to B and from B to A, and the routing tables on both routers are correct, only then e-mail your completed RSM file and configuration text file to me for grading.
    • E-mail Subject: CST3607 Lab-04 YourLastName
  • Note: Do not use “version 2” when configuring RIP
  • Important: Lab-04 is required, as it is the starting point/baseline for future labs.

Troubleshooting Your Lab?

  • Did you enable all the required interfaces on all the routers? no shutdown
  • Have you checked all the router interfaces to make sure that both Status and Protocol are both up? show ip interface brief
  • Did you check that the clockrate on the DCE interface is set and greater than zero?
  • Did you add only the directly connected networks to the routing protocol?
  • Did you use the interface’s IP address instead of it’s network address when configuring the routing protocol?
  • Did you use the wildcard mask, not the subnet mask, when configuring OSPF?
  • When you ping a host or router, where is the ICMP request failing to get to its destination?
  • Still having problems? And you’re confident that your configuration is correct? Save the lab, exit RouterSim, and then reload the lab.

Study for Exam #2